Industrial water treatment chemicals · Manufacturer & global B2B supply[email protected] · +86 177 3480 9172
RYZE Technology logoRYZETECHNOLOGY
TECHNICAL NOTE

PAC: specification, dosage and clarification

Polyaluminium chloride is sold by Al2O3 content and basicity, but plants buy it by the tonne and pay for it by the cubic metre. The two numbers are not the same.

Last updated: 2026-11-18Technical article

Quick answer: PAC is a pre-hydrolysed aluminium coagulant, normally dosed at 20–150 ppm of product (5–40 ppm as Al2O3), with an optimum pH of about 6.0–8.0. Higher Al2O3 and basicity mean less inert salt per tonne; the dose that matters is the one found by jar test on your own water.

What PAC does

PAC supplies partially hydrolysed aluminium species that neutralise colloidal charge and form a hydroxide floc that sweep-removes turbidity, colour, some COD and phosphate. Because it is already partly hydrolysed, it reacts faster and consumes less alkalinity than aluminium sulfate, and it works over a wider pH band.

Compared withPAC advantagePAC limitation
Aluminium sulfateLess alkalinity consumption, faster floc, wider pHHigher price per tonne of product
Ferric chlorideNo chloride load, no strong colourLower phosphorus removal per mole of metal
PFSLower iron residual, no staining in some usesLess effective for colour and sulphide in some waters

Read the specification correctly

ParameterWhat it meansWhat to watch
Al2O3 contentActive coagulant per tonne26%, 28% and 30% differ by roughly 15% in active content — compare cost per kg Al2O3, not per tonne
BasicityDegree of pre-hydrolysis, 40–85%Higher basicity = less alkali demand and less pH drop, but can be less stable in storage
pH of 1% solution3.5–5.0 typicalVery low pH signals strong acidity and a bigger alkalinity hit
InsolublesInert residueHigh insolubles mean sludge and blocked dosing lines
Heavy metalsPotable-water complianceRequired for drinking-water grade; ask for the COA

A "30% PAC" at a low basicity can perform worse than a 28% at high basicity in soft water, because the plant then pays for alkali as well.

Setting the dose

  1. Run a jar test at the plant's actual pH, not at the pH you wish you had.
  2. Use a dose series: 10, 20, 40, 60, 80, 100 ppm as product.
  3. Rapid mix 60 seconds at high energy, then slow mix 15 minutes.
  4. Let settle 20–30 minutes; measure turbidity, pH and, if relevant, phosphate.
  5. Choose the lowest dose where turbidity stops improving — beyond that, you are buying sludge, not clarity.

Typical results: surface water 10–40 ppm; municipal secondary effluent 20–60 ppm; industrial effluent 40–150 ppm; phosphorus-driven dosing often 1.5–3 moles Al per mole P.

The pH window

The optimum is 6.0–8.0 for PAC, narrower for low-alkalinity water. Two failure patterns:

  • pH below 5.5 — the floc does not form properly and residual aluminium rises.
  • pH above 8.5 — aluminate formation, poor floc, high aluminium residual.

Check alkalinity before increasing dose. If alkalinity is below about 40 mg/L as CaCO3, a coagulant will drive pH down and the plant will chase its own tail.

When PFS is better

Polyferric sulfate suits colour removal, sulphide-bearing water, cold water and cases where a denser floc is wanted. Iron residual and staining are the trade-offs. In potable water, check the iron limit in the local standard before switching.

Common mistakes

  • Comparing products per tonne instead of per kg Al2O3.
  • Increasing the dose when the real issue is mixing energy or pH.
  • Using a potable grade specification for an industrial application, which raises cost with no benefit.
  • Storing liquid PAC in heat and sunlight; stability drops and dosing lines clog.

Send pH, alkalinity, turbidity or SS, and phosphate. We return a grade, a dose band and the jar-test sheet you can run in the plant laboratory.

Questions buyers ask

Direct answers

What does basicity mean in PAC?

It is the degree of pre-hydrolysis: the proportion of aluminium already in hydroxyl form. Higher basicity means less acid released and less alkalinity consumed, but very high basicity products can be less stable in storage.

Is 30% PAC always better than 28%?

Per tonne of active Al2O3 yes, but per cubic metre treated it depends on basicity, insolubles and the plant's pH. Compare on cost per kg Al2O3 and on the jar-test dose.

Why does PAC stop working when we raise the dose?

Beyond the optimum the floc becomes brittle, pH falls and residual aluminium rises. If clarity does not improve between two consecutive doses, the limit is pH or mixing, not dose.

Can PAC be used in drinking water?

Yes, with a grade that meets the potable-water standard and the corresponding COA. State the final use in the inquiry; industrial grade is not interchangeable.

Send your water or material data.

We reply with a product route, indicative dosage and the documents you need.

Contact technical sales ↗