Industrial water treatment chemicals · Manufacturer & global B2B supply[email protected] · +86 177 3480 9172
RYZE Technology logoRYZETECHNOLOGY
TECHNICAL NOTE

How to choose a polyacrylamide grade

Anionic, cationic or nonionic is decided by the charge of your solids — not by price, not by what the previous supplier sold you, and not by the label on the bag.

Last updated: 2026-11-18Technical article

Quick answer: use cationic PAM for organic and biological sludge, anionic PAM for mineral slurries such as tailings, coal and metal hydroxide sludge, and nonionic PAM only for acidic or low-turbidity systems. Then match molecular weight to the separation equipment and charge density to the colloid load, and confirm with a jar test on the real water.

The one-minute answer

Your materialStart withWhy
Waste-activated sludge, digested sludgeCationic, medium molecular weightOrganic solids carry negative charge; cationic polymer neutralises and bridges
Belt press or centrifuge feedCationic, medium to high charge densityCharge demand is high; overdosing shows as sticky, wet cake
Mineral tailings, coal slimeAnionic, high molecular weightMineral particles need long chains for fast settling
Metal hydroxide sludgeAnionic, medium molecular weightFloc must be tough enough for a filter press
Paper stock retentionCationic, low molecular weightShort chains work at the headbox, long chains over-flocculate
Acidic or low-turbidity suspensionNonionicCharge-neutral bridging where pH limits ionisation

Charge type decides the family

Colloidal particles carry a surface charge. Most organic and biological solids are negative, so a positively charged polymer both neutralises the charge and bridges the particles. Mineral particles are usually negative too, but the suspension is dense and the goal is settling speed rather than charge neutralisation, which is why anionic high-molecular-weight grades dominate in mining.

A simple field check: add a drop of anionic and a drop of cationic stock solution to two beakers of the same slurry. Whichever produces visible flocs within 30 seconds is the right family. If neither does, the suspension needs coagulation first — the polymer has nothing to bridge.

Molecular weight decides the speed

Molecular weightSettlingShear toleranceTypical use
Low (5–8 million)SlowerGoodRetention aids, filtration, fine floc
Medium (8–15 million)BalancedModerateSludge dewatering, belt press, centrifuge
High (15–25 million)FastPoorThickeners, tailings, high-solids clarification

Higher molecular weight is not automatically better. In a centrifugal pump or a high-shear mixer, a very high molecular weight floc breaks apart and the plant compensates by buying more polymer. If the slurry passes through a pump after flocculation, choose medium.

Charge density decides the dose

Charge density is the fraction of the polymer chain that carries charge. Higher density neutralises more charge per kilogram but narrows the operating window: a small overdose collapses the floc or makes the cake sticky.

  • Low density (10–20%): tolerant, good for variable sludge.
  • Medium (20–40%): the usual starting point for municipal sludge.
  • High (40–60%): blood-rich, fat-rich or highly colloidal sludge; also some paper applications.

A charge-demand test — titrating the sludge with a standard cationic polymer until the supernatant clears — gives the number directly and usually explains why a plant is consuming twice the expected dose.

The jar test that settles it

  1. Take fresh sample, do not let it settle for hours before testing.
  2. Divide into six beakers of equal volume.
  3. Add coagulant first if the suspension is colloidal, mix fast for 60 seconds.
  4. Add polymer at 0.5, 1, 2, 4, 8 ppm equivalents; invert the beakers the same number of times.
  5. Watch three things: time to first visible floc, floc size, and clarity of the supernatant after 5 minutes.
  6. Record the dose where clarity stops improving — that is the knee of the curve, and the practical set point is usually 10–20% below it.

For dewatering, finish with a "cake" test: pour the flocculated sludge onto a 200-mesh screen or a piece of filter cloth and observe drainage time and cake firmness. Settling clarity and dewatering quality are not the same thing, and a grade that wins the settle test can lose the press test.

The data to send a supplier

  • Suspended solids, pH, and the material type (biological, mineral, chemical).
  • Equipment: thickener, DAF, belt press, centrifuge, filter press, and the target cake solids.
  • Current product, dose and the result you are getting.
  • A 2–5 kg sample if a real trial is needed.

With those four items a supplier can shortlist one or two grades in a day. Without them, any recommendation is a guess with a datasheet attached.

Questions buyers ask

Direct answers

Can we mix anionic and cationic PAM?

No. The charges neutralise each other and both products are wasted. If the process needs two stages, separate them in time and in tank.

Does higher molecular weight always save money?

No. In sheared systems the floc breaks and the plant buys more polymer. Medium molecular weight often costs less per tonne treated in a belt press house.

How long does a PAM stock solution last?

About 24–48 hours at 0.1–0.3%. After that viscosity and performance drop, especially in warm plants. Prepare smaller batches more often.

Why is our dose twice the supplier's recommendation?

Usually incomplete dissolution, polymer aging, an upstream coagulant overdose, or a change in sludge age. Check dissolution and stock age first; they are the cheapest explanations.

Send your water or material data.

We reply with a product route, indicative dosage and the documents you need.

Contact technical sales ↗